PYQ Vault

NEET Physics · Alternating Current

Series LCR Circuit and Resonance

A resistor, inductor and capacitor in series on ac: the impedance and phase angle, resonance when the two reactances cancel, and the power the circuit takes.

Why this matters

Eight NEET questions from 2021 to 2026, the busiest page of the chapter. Three find an impedance or current (from three voltmeter readings in 2021, from a circuit figure in 2023, the current and phase angle in 2025), four are about resonance (the resonant frequency in 2022, 2023 and 2026, the current at resonance in Re-NEET 2026) and one asks for the two half-power frequencies (2021).

Concept 1 of 3: Impedance and phase angle

In series the same current flows through R, L and C. The voltage across R is in step with it, the voltage across L is a quarter cycle ahead and the voltage across C a quarter cycle behind. So the L and C voltages point opposite ways and partly cancel. What is left adds to the resistor's voltage at right angles, like the two short sides of a right triangle. The total opposition of the circuit is its impedance.

Definition

  • The same current I flows in R, L and C: VR=IRV_R = IR, VL=IXLV_L = IX_L, VC=IXCV_C = IX_C.
  • Supply voltage: V=VR2+(VL−VC)2V = \sqrt{V_R^{2} + (V_L - V_C)^{2}}. The three voltages add as phasors, not as plain numbers.
  • Impedance: Z=R2+(XL−XC)2Z = \sqrt{R^{2} + (X_L - X_C)^{2}}, in ohm. Then I=VZI = \dfrac{V}{Z}, rms with rms or peak with peak.
  • Phase angle between the current and the supply voltage: tan⁡ϕ=XL−XCR\tan\phi = \dfrac{X_L - X_C}{R}.
  • If XL>XCX_L > X_C the circuit is inductive and the current lags the voltage. If XC>XLX_C > X_L it is capacitive and the current leads.

Series LCR

Z=R2+(XL−XC)2,tan⁡ϕ=XL−XCR,V=VR2+(VL−VC)2Z = \sqrt{R^{2} + (X_L - X_C)^{2}}, \qquad \tan\phi = \frac{X_L - X_C}{R}, \qquad V = \sqrt{V_R^{2} + (V_L - V_C)^{2}}
  • ZZimpedance
  • ϕ\phiphase angle between current and voltage

Animation · series LCR voltages added as phasors

The resultant Vcurrent IφVR 30 VVL 90 VVC 50 V40 VV = 50 VVR = 30 VVL = 90 V (ahead)VC = 50 V (behind)90 − 50 = 40 VV = √(30² + 40²) = 50 Vtan φ = 40/30, φ ≈ 53°not 30 + 90 + 50 = 170 V
  1. The resistor's voltage, along the current: The current is the same in R, L and C, so it is the reference. The voltage across the resistor, 30 V, is in phase with it.
  2. The inductor's voltage, 90° ahead: The voltage across the inductor, 90 V, leads the current by 90°, so its arrow stands straight up.
  3. The capacitor's voltage, 90° behind: The voltage across the capacitor, 50 V, lags the current by 90°, so its arrow points straight down, opposite to the inductor's.
  4. Combine the inductor and capacitor voltages: They are 180° apart, so they cancel in part: 90 − 50 = 40 V, still upward because the inductor's is larger.
  5. The resultant V: The supply voltage is the hypotenuse: V = √(30² + 40²) = 50 V, not 30 + 90 + 50. tan φ = 40/30, so φ ≈ 53°, the voltage leading the current.

Lengths are to scale. Up is 90° ahead of the current, down is 90° behind.

Worked example

In a series LCR circuit, ac voltmeters read 60 V across R, 120 V across L and 40 V across C. Find the supply voltage and say whether the current leads or lags it, and by what angle.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2025 · NEET (UG) 2025 — 04 May 2025 · Q16Moderate

Example 1 · Alternating Current · Series LCR Circuit and Resonance

To an ac power supply of 220 V at 50 Hz, a resistor of 20 Ω\Omega, a capacitor of reactance 25 Ω\Omega and an inductor of reactance 45 Ω\Omega are connected in series. The corresponding current in the circuit and the phase angle between the current and the voltage is, respectively

Voltages add as phasors

Readings of 40 V across L, 10 V across C and 40 V across R do not make a 90 V supply. The supply is 402+(40−10)2=50 V\sqrt{40^{2} + (40 - 10)^{2}} = 50\ \text{V}.

Subtract the reactances

XLX_L and XCX_C act in opposite directions, so the impedance uses XL−XCX_L - X_C. Adding them gives an impedance that is too large.

Keep peak with peak

Z=VIZ = \dfrac{V}{I} holds with both values rms or both peak. If the current amplitude is given, divide it by 2\sqrt{2} before using it with an rms voltage.

Concept 2 of 3: Resonance in a series LCR circuit

As the frequency rises, the inductor's reactance grows and the capacitor's falls. At one frequency the two are equal and cancel completely. Then only the resistor is left to oppose the current, so the impedance is the smallest it can be and the current the largest. This is resonance, and it is how a radio picks one station out of many.

Definition

  • Resonance happens when XL=XCX_L = X_C, that is ωL=1ωC\omega L = \dfrac{1}{\omega C}.
  • Resonant angular frequency ω0=1LC\omega_0 = \dfrac{1}{\sqrt{LC}} in rad/s; resonant frequency f0=12πLCf_0 = \dfrac{1}{2\pi\sqrt{LC}} in hertz.
  • At resonance Z=RZ = R, the current amplitude is largest, I0=V0RI_0 = \dfrac{V_0}{R}, and the current is in phase with the voltage.
  • The voltages across L and C are equal in size and opposite in phase, so they cancel.
  • The resonant frequency depends on L and C only. R decides how large the current is at resonance, not where resonance happens.
  • To test whether a source drives a circuit at resonance, work out XLX_L and XCX_C at the source's ω\omega and compare them.

Resonance

ω0=1LC,f0=12πLC,Zmin⁡=R\omega_0 = \frac{1}{\sqrt{LC}}, \qquad f_0 = \frac{1}{2\pi\sqrt{LC}}, \qquad Z_{\min} = R

Visualization · current against frequency in a series LCR circuit

024681004080120160current I (A)frequency f (Hz)f₀ ≈ 79.6 Hzwidth 15.9 HzI = V/R = 5.0 A

At f₀: Z = R = 40 Ω, I = 200/40 = 5.0 A, φ = 0

f₀ = 1/(2π√(LC)) with L = 0.4 H, C = 10 μF: 79.6 Hz, whatever R is

Far below f₀ the capacitor's large reactance limits the current, far above it the inductor's does. At f₀ they cancel and only R is left, so Z is least (never zero). A smaller R gives a taller, narrower peak: the circuit picks out f₀ more sharply. The amber line marks where I is above Iₘₐₓ/√2; its width is R/(2πL).

Worked example

A coil of inductance 0.1 H and resistance 20 Ω is to resonate at ω=1000\omega = 1000 rad/s with a capacitor in series, on a 10 V rms supply. What capacitance is needed, and what rms current flows at resonance?
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2026 · NEET (UG) 2026 — 03 May 2026 · Q19Moderate

Example 2 · Alternating Current · Series LCR Circuit and Resonance

An ac circuit contains a resistance of 1 kΩ\Omega, a capacitor of 0.1 μ\muF and an inductor of 1 mH connected in series. The resonance frequency of the circuit is approximately:

rad/s or hertz

1LC\dfrac{1}{\sqrt{LC}} is the angular frequency in rad/s. Divide by 2π2\pi for hertz. With L = 10 mH and C = 1 μF, ω0=104\omega_0 = 10^{4} rad/s but f0≈1.59f_0 \approx 1.59 kHz.

Resistance does not move resonance

The resonant frequency depends on L and C only. A resistance given in the question changes the current at resonance, never f0f_0.

Convert milli and micro first

Put L in henry and C in farad before using 1LC\dfrac{1}{\sqrt{LC}}: 10 mH is 10−210^{-2} H and 1 μF is 10−610^{-6} F.

Concept 3 of 3: Power, power factor and half-power frequencies

Only the resistor turns electrical energy into heat. An inductor or a capacitor takes energy in one quarter cycle and gives it back in the next. So the average power depends on how much of the current is in step with the voltage, and that share is the power factor. Near resonance the power is large; move the frequency away and it falls. The two frequencies where it has fallen to half mark how sharp the resonance is.

Definition

  • Average power: P=VrmsIrmscos⁡ϕP = V_{rms}I_{rms}\cos\phi. The factor cos⁡ϕ=RZ\cos\phi = \dfrac{R}{Z} is the power factor.
  • Since only R uses energy, P=Irms2RP = I_{rms}^{2}R as well.
  • Pure resistor: cos⁡ϕ=1\cos\phi = 1. Pure inductor or capacitor: ϕ=90∘\phi = 90^{\circ}, cos⁡ϕ=0\cos\phi = 0, no power is used, and the current is called wattless.
  • At resonance cos⁡ϕ=1\cos\phi = 1 and the power is the largest, Vrms2R\dfrac{V_{rms}^{2}}{R}.
  • Half-power frequencies: the power is half its resonant value when the current is 12\dfrac{1}{\sqrt{2}} of its resonant value, that is when Z=2RZ = \sqrt{2}R. For a sharp resonance these are ω=ω0±R2L\omega = \omega_0 \pm \dfrac{R}{2L}, so they are RL\dfrac{R}{L} apart (the bandwidth).
  • A smaller R gives a narrower, sharper resonance.

Power in ac

P=VrmsIrmscos⁡ϕ,cos⁡ϕ=RZ,ω1,2=ω0±R2LP = V_{rms} I_{rms} \cos\phi, \qquad \cos\phi = \frac{R}{Z}, \qquad \omega_{1,2} = \omega_0 \pm \frac{R}{2L}

Worked example

A circuit draws an rms current of 2 A from a 200 V rms supply, with the current lagging the voltage by 60°. Find the average power and the power factor.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2021 · NEET (UG) 2021 — 12 Sep 2021 · Q40Moderate

Example 3 · Alternating Current · Series LCR Circuit and Resonance

A series LCR circuit containing 5.0 H inductor, 80 μ\muF capacitor and 40 Ω\Omega resistor is connected to 230 V variable frequency ac source. The angular frequencies of the source at which power transferred to the circuit is half the power at the resonant angular frequency are likely to be

Use rms values for power

P=VIcos⁡ϕP = V I\cos\phi needs rms values. With peak values the power is 12V0I0cos⁡ϕ\dfrac{1}{2}V_0I_0\cos\phi.

Half power is not half current

At a half-power frequency the current is 12\dfrac{1}{\sqrt{2}} of its resonant value, not half. Each half-power frequency sits R2L\dfrac{R}{2L} from ω0\omega_0, so the two are RL\dfrac{R}{L} apart.

Summary — formulas & gotchas at a glance

A revision cheat-sheet for the formulas and gotchas above. Click any concept name to jump back to its full explanation.

Formulas (3)

  • Impedance and phase angle

    Series LCR

    Z=R2+(XL−XC)2,tan⁡ϕ=XL−XCR,V=VR2+(VL−VC)2Z = \sqrt{R^{2} + (X_L - X_C)^{2}}, \qquad \tan\phi = \frac{X_L - X_C}{R}, \qquad V = \sqrt{V_R^{2} + (V_L - V_C)^{2}}
  • Resonance in a series LCR circuit

    Resonance

    ω0=1LC,f0=12πLC,Zmin⁡=R\omega_0 = \frac{1}{\sqrt{LC}}, \qquad f_0 = \frac{1}{2\pi\sqrt{LC}}, \qquad Z_{\min} = R
  • Power, power factor and half-power frequencies

    Power in ac

    P=VrmsIrmscos⁡ϕ,cos⁡ϕ=RZ,ω1,2=ω0±R2LP = V_{rms} I_{rms} \cos\phi, \qquad \cos\phi = \frac{R}{Z}, \qquad \omega_{1,2} = \omega_0 \pm \frac{R}{2L}

Watch out for (8)

Test yourself on a real paper

Sit a past NEET paper, timed and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.

Sit a NEET past paper