NEET Physics · Electromagnetic Induction
Induced EMF and Lenz's Law
Magnetic flux Φ = BA cos θ, the emf ε = −N dΦ/dt induced when that flux changes, Lenz's law for its direction and eddy currents, the emf Blv of a moving rod, and the emf NBAω sin ωt of a rotating coil.
Why this matters
Six NEET questions from 2022 to 2026: two each from 2022, 2024 and 2026. Two use flux and Faraday's law (the flux through a square loop in 2022, the power in a loop whose area changes with time in Re-NEET 2026), two use Lenz's law (the current in two solenoids as a magnet moves between them, and which sheets near a magnet pole need a force, both in 2024), one asks for the emf across the cut in a loop leaving a field (2026) and one for the peak current in a rotating coil (2022).
Concept 1 of 4: Magnetic flux and Faraday's law
Definition
- Flux: , with the angle between and the normal to the loop. SI unit: the weber, .
- Plane of the loop perpendicular to B: and . Plane parallel to B: .
- Faraday's law: ; for a coil of N turns, . Over a finite change, the average emf is .
- The flux changes if B, A or changes. Field changing, area fixed and normal to B: .
- In a closed loop of resistance R: current and power .
Flux and Faraday's law
- angle between the field and the normal to the loop
- number of turns
- resistance of the closed loop
Worked example
Practise this conceptself-check · 4 quick reps
The same idea in a real exam question:
Example 1 · Electromagnetic Induction · Induced EMF and Lenz's Law
The angle is measured from the normal
Emf comes from a change, not from the flux
Power is never negative
Concept 2 of 4: Lenz's law and eddy currents
Definition
- Lenz's law: the induced emf drives a current that opposes the change in magnetic flux that produced it. It is the minus sign in , and it follows from conservation of energy.
- Looking at one face of a coil: an anticlockwise current makes that face a north pole, a clockwise current a south pole.
- Steps for a direction: which way does the flux point, is it growing or falling, the induced field points against a growth and along a fall, then the right-hand rule gives the current.
- Eddy currents are induced in a bulk piece of conductor when the flux through it changes. They oppose the motion that causes them and heat the metal.
- Cutting slots in a metal plate, or building a core from thin insulated sheets, breaks up the eddy-current paths and makes them smaller.
- Uses of eddy currents: electromagnetic damping (a swinging metal plate between magnet poles soon stops), magnetic braking in some trains, and induction furnaces that melt metals.
Animation · Lenz's law with a magnet and a coil
- Magnet at rest: The magnet's N pole faces the coil. Nothing moves, so the flux through the coil does not change and no current is induced.
- N pole moves in: The flux through the coil rises. The induced current flows anticlockwise as seen from the magnet, so the near face becomes a N pole and repels the magnet.
- Magnet stops: The flux is large but steady, so there is no current. Lenz's law opposes a change in flux, not the flux itself.
- N pole moves away: The flux falls, so the current reverses: clockwise as seen from the magnet. The near face becomes a S pole and attracts the magnet back.
- The rule: Pushing the magnet in or pulling it out, you work against a force. That work is the energy the current carries, which is why Lenz's law is conservation of energy.
Below the coil: its near face as seen from the magnet's side. An anticlockwise current makes that face a N pole, a clockwise one a S pole.
| Situation | What the flux does | What happens |
|---|---|---|
| North pole pushed towards a coil | Flux through the coil grows | Near face becomes a north pole; the magnet is repelled |
| North pole pulled away from a coil | Flux through the coil falls | Near face becomes a south pole; the magnet is attracted back |
| South pole pushed towards a coil | Flux through the coil grows | Near face becomes a south pole; the magnet is repelled |
| Magnet held at rest near a coil | Stays the same | No emf and no current |
| Conducting sheet moved near a strong magnet pole | Changes in parts of the sheet | Eddy currents oppose the motion, so a force is needed even to move it at steady speedQ NEET 2024: of four sheets near a strong pole, a force is needed to hold a magnetic one and to move a conducting one at uniform speed. |
| Non-conducting, non-magnetic sheet near a magnet | No current can flow in it | No eddy currents and no magnetic force |
| Metal plate swinging between magnet poles | Changes as the plate swings | Eddy currents damp it quickly; a slotted plate swings much longer |
Practise this conceptself-check · 4 quick reps
The same idea in a real exam question:
Example 2 · Electromagnetic Induction · Induced EMF and Lenz's Law
Opposing the change, not the flux
Holding a sheet still is not induction
Eddy currents need a conductor
Concept 3 of 4: Motional emf of a moving rod
Definition
- A rod of length l moving with speed v, with B, l and v all perpendicular to one another: .
- If the rod moves along its own length, no emf appears between its ends.
- Rod sliding on rails, circuit resistance R: . The field pushes on the current with , opposite to the motion. Power to keep it moving: .
- A loop moving out of (or into) a field: only the side that cuts the field lines matters, so l is the side perpendicular to the velocity.
- A closed loop moving wholly inside a uniform field keeps the same flux, so it has no net emf.
Motional emf
- length of the conductor that cuts the field, perpendicular to v
- speed of the conductor
Worked example
Practise this conceptself-check · 4 quick reps
The same idea in a real exam question:
Example 3 · Electromagnetic Induction · Induced EMF and Lenz's Law
Using the wrong side of the loop
A loop wholly inside the field
Concept 4 of 4: Emf of a rotating coil (AC generator)
Definition
- A coil of N turns and area A turning at angular speed in a field B, about an axis perpendicular to B: .
- Emf: , with peak value . Peak current .
- Emf is zero when the plane of the coil is perpendicular to B (flux largest), and largest when the plane is parallel to B (flux zero).
- , where is the number of turns per second.
- Only the component of B perpendicular to the axis of rotation changes the flux.
AC generator
- angular speed of the coil
- revolutions per second
Worked example
Practise this conceptself-check · 4 quick reps
The same idea in a real exam question:
Example 4 · Electromagnetic Induction · Induced EMF and Lenz's Law
Largest emf at zero flux
Revolutions per second are not radians per second
Only the field across the axis counts
Summary — formulas & gotchas at a glance
A revision cheat-sheet for the formulas and gotchas above. Click any concept name to jump back to its full explanation.
Formulas (3)
- Magnetic flux and Faraday's law
Flux and Faraday's law
- Motional emf of a moving rod
Motional emf
- Emf of a rotating coil (AC generator)
AC generator
Reference tables (1)
Lenz's law and eddy currents7 rows
| Situation | What the flux does | What happens |
|---|---|---|
| North pole pushed towards a coil | Flux through the coil grows | Near face becomes a north pole; the magnet is repelled |
| North pole pulled away from a coil | Flux through the coil falls | Near face becomes a south pole; the magnet is attracted back |
| South pole pushed towards a coil | Flux through the coil grows | Near face becomes a south pole; the magnet is repelled |
| Magnet held at rest near a coil | Stays the same | No emf and no current |
| Conducting sheet moved near a strong magnet pole | Changes in parts of the sheet | Eddy currents oppose the motion, so a force is needed even to move it at steady speedQ NEET 2024: of four sheets near a strong pole, a force is needed to hold a magnetic one and to move a conducting one at uniform speed. |
| Non-conducting, non-magnetic sheet near a magnet | No current can flow in it | No eddy currents and no magnetic force |
| Metal plate swinging between magnet poles | Changes as the plate swings | Eddy currents damp it quickly; a slotted plate swings much longer |
Watch out for (11)
- The angle is measured from the normal→ Magnetic flux and Faraday's law
- Emf comes from a change, not from the flux→ Magnetic flux and Faraday's law
- Power is never negative→ Magnetic flux and Faraday's law
- Opposing the change, not the flux→ Lenz's law and eddy currents
- Holding a sheet still is not induction→ Lenz's law and eddy currents
- Eddy currents need a conductor→ Lenz's law and eddy currents
- Using the wrong side of the loop→ Motional emf of a moving rod
- A loop wholly inside the field→ Motional emf of a moving rod
- Largest emf at zero flux→ Emf of a rotating coil (AC generator)
- Revolutions per second are not radians per second→ Emf of a rotating coil (AC generator)
- Only the field across the axis counts→ Emf of a rotating coil (AC generator)
Test yourself on a real paper
Sit a past NEET paper, timed and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.