PYQ Vault

NEET Physics · Current Electricity

Power, Cells and EMF

Electrical power P = VI = I²R = V²/R and what a power rating fixes, then a cell's emf, its internal resistance and the terminal voltage it delivers.

Why this matters

Five NEET questions from 2022 to 2026, four of them from 2024 or later. Three are about power: the heat shared by two resistors in parallel, two heaters joined in series and then in parallel, and a heater run on a lower supply. Two ask for a cell's terminal voltage from its emf and internal resistance.

Concept 1 of 2: Electrical power and ratings

A resistor turns electrical energy into heat at the rate P = VI. A rating like 220 V, 400 W fixes one thing that never changes, the device's resistance R = V²/P. On a different supply, or joined with other devices, R stays and the power changes. Pick the form of the power formula that holds fixed what the circuit holds fixed: the current in series, the voltage in parallel.

Definition

  • P=VI=I2R=V2RP = VI = I^{2}R = \dfrac{V^{2}}{R}. Heat in a time t: H=I2RtH = I^{2}Rt.
  • From a rating: R=V02P0R = \dfrac{V_0^{2}}{P_0}. On a supply V: P=P0(VV0)2P = P_0\left(\dfrac{V}{V_0}\right)^{2}.
  • In series (same current): P∝RP \propto R. In parallel (same voltage): P∝1RP \propto \dfrac{1}{R}.
  • Two devices rated P1P_1 and P2P_2 at the same voltage, used on that voltage: in parallel the total is P1+P2P_1 + P_2; in series P1P2P1+P2\dfrac{P_1P_2}{P_1 + P_2}.

Power

P=VI=I2R=V2R,R=V02P0,P=P0(VV0)2P = VI = I^{2}R = \frac{V^{2}}{R}, \qquad R = \frac{V_0^{2}}{P_0}, \qquad P = P_0\left(\frac{V}{V_0}\right)^{2}

Worked example

A 220 V, 100 W bulb and a 220 V, 25 W bulb are joined in series across 220 V. Which glows brighter, and what is the total power drawn?
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2024 · NEET (UG) 2024 — 05 May 2024 · Q44Moderate

Example 1 · Current Electricity · Power, Cells and EMF

Two heaters A and B have power rating of 1 kW and 2 kW, respectively. Those two are first connected in series and then in parallel to a fixed power source. The ratio of power outputs for these two cases is:

In parallel the smaller resistor heats more

Parallel resistors share a voltage, so heat goes as V2/RV^{2}/R: the smaller resistor gives more heat. Using I2RI^{2}R with one current gets the order backwards.

Power goes as the square of the voltage

Dropping a supply from 220 V to 200 V does not cut the power by 20/220. Square the factor: (200/220)2(200/220)^{2} is about 0.83.

In series the lower rating glows more

A 25 W bulb has more resistance than a 100 W bulb of the same voltage, so with the same current it dissipates more. In parallel the order flips.

Concept 2 of 2: Emf, internal resistance and terminal voltage

A cell is a source of emf E with a small resistance r inside it, the electrolyte between its plates. When the cell drives a current, part of its emf is used up pushing that current through r. What is left across its terminals, the terminal voltage, is less than E. With no current, the terminal voltage equals the emf.

Definition

  • Current from a cell into an external resistor R: I=ER+rI = \dfrac{E}{R + r}.
  • Terminal voltage while the cell supplies current: V=E−Ir=ERR+rV = E - Ir = \dfrac{ER}{R + r}. With no current V=EV = E.
  • Short circuit (R = 0): the largest current, Er\dfrac{E}{r}.
  • Cells in series: Eeq=E1+E2E_{eq} = E_1 + E_2 and req=r1+r2r_{eq} = r_1 + r_2 (a cell joined the other way round subtracts its emf).
  • Two cells in parallel: Eeq=E1r2+E2r1r1+r2E_{eq} = \dfrac{E_1r_2 + E_2r_1}{r_1 + r_2}, req=r1r2r1+r2r_{eq} = \dfrac{r_1r_2}{r_1 + r_2}. For n identical cells: E and rn\dfrac{r}{n}.

Terminal voltage

I=ER+r,V=E−Ir,Eeq=E1r2+E2r1r1+r2I = \frac{E}{R + r}, \qquad V = E - Ir, \qquad E_{eq} = \frac{E_1r_2 + E_2r_1}{r_1 + r_2}

Worked example

A cell of emf 6 V and internal resistance 0.5 Ω is joined to a 2.5 Ω resistor. Find the current and the terminal voltage.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2026 · NEET (UG) 2026 — 03 May 2026 · Q6Easy

Example 2 · Current Electricity · Power, Cells and EMF

A resistor is connected to a battery of 12 V emf and internal resistance 2 Ω2\,\Omega. If the current in the circuit is 0.6 A, the terminal voltage of the battery is:

Subtract only the drop inside the cell

Terminal voltage is E−IrE - Ir, with the internal resistance r. Subtracting IRIR with the external resistance gives zero, not the terminal voltage.

Parallel cells do not add their emfs

Identical cells in parallel keep the emf of one cell and divide the internal resistance by n. Only cells in series add their emfs.

Summary — formulas & gotchas at a glance

A revision cheat-sheet for the formulas and gotchas above. Click any concept name to jump back to its full explanation.

Formulas (2)

  • Electrical power and ratings

    Power

    P=VI=I2R=V2R,R=V02P0,P=P0(VV0)2P = VI = I^{2}R = \frac{V^{2}}{R}, \qquad R = \frac{V_0^{2}}{P_0}, \qquad P = P_0\left(\frac{V}{V_0}\right)^{2}
  • Emf, internal resistance and terminal voltage

    Terminal voltage

    I=ER+r,V=E−Ir,Eeq=E1r2+E2r1r1+r2I = \frac{E}{R + r}, \qquad V = E - Ir, \qquad E_{eq} = \frac{E_1r_2 + E_2r_1}{r_1 + r_2}

Watch out for (5)

Test yourself on a real paper

Sit a past NEET paper, timed and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.

Sit a NEET past paper