PYQ Vault

NEET Physics · Mechanical Properties of Solids

Stress, Strain and Young's Modulus

Stress as restoring force per unit area and strain as a fractional change, Hooke's law and Young's modulus (ΔL = FL/AY), the elastic limit, and the stress in a rod that is heated but not allowed to expand.

Why this matters

Three NEET questions, from 2023 and 2024. NEET 2023 asks for the stress in a wire holding a block. NEET 2024 asked twice: the largest stretch of a steel wire from its elastic limit and Young's modulus, and the force in a heated bar that is not allowed to expand.

Concept 1 of 3: Stress, strain and Hooke's law

Pull on a wire and it stretches a little. Inside it, the particles pull back, and that restoring force spread over the cross-section is the stress. How much the wire has stretched compared with its length is the strain. For small stretches the two are in proportion: double the stress and the strain doubles. That is Hooke's law.

Definition

  • Stress = restoring force per unit area, FA\dfrac{F}{A}. Unit N m⁻², called the pascal (Pa).
  • Longitudinal strain =ΔLL= \dfrac{\Delta L}{L}. Stretching gives tensile stress, squeezing gives compressive stress.
  • Shearing strain =ΔxL=tan⁡θ= \dfrac{\Delta x}{L} = \tan\theta, when a force acts along a face and the opposite face is held.
  • Volume strain =ΔVV= \dfrac{\Delta V}{V}, when a body is pressed equally from all sides (hydraulic stress).
  • Strain is a ratio of two lengths or two volumes, so it has no unit.
  • Hooke's law: for small deformations, stress is proportional to strain.

Stress and strain

stress=FA,longitudinal strain=ΔLL,stress∝strain\text{stress} = \frac{F}{A}, \qquad \text{longitudinal strain} = \frac{\Delta L}{L}, \qquad \text{stress} \propto \text{strain}
  • FFforce acting on the cross-section
  • AAarea of cross-section
  • ΔL\Delta Lchange in length

Worked example

A concrete column with a cross-section of 0.5 m² and a height of 4 m supports a load of 5×1055 \times 10^{5} N, and its height shrinks by 0.2 mm. Find the compressive stress and the strain.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2023 · NEET (UG) 2023 — 07 May 2023 · Q16Easy

Example 1 · Mechanical Properties of Solids · Stress, Strain and Young's Modulus

A block of weight WW is suspended from a wire of uniform cross-sectional area AA as shown. The longitudinal stress at any point of cross-sectional area AA of the wire is

Stress uses the area of cross-section

Divide the force by the area it acts across, the cross-section of the wire, not by the outer surface area of the wire.

Strain has no unit

Strain is a change in length divided by a length, so the units cancel. Stress has the unit of pressure, N m⁻²; the two are not the same kind of quantity.

A light wire holding a load has the same stress all along it

Every cross-section of a light wire holding a block of weight W carries the same tension W, so the stress is WA\dfrac{W}{A} at every point, not half of it in the middle.

Concept 2 of 3: Young's modulus and the elastic limit

Young's modulus measures how hard a material is to stretch. A large Y means a big stress gives only a small strain, as in steel. It belongs to the material, so a long thin wire and a short thick one of the same steel have the same Y even though they stretch by different amounts. Hooke's law only holds up to the elastic limit; pull harder and the wire no longer returns to its length.

Definition

  • Young's modulus: Y=stressstrain=FLAΔLY = \dfrac{\text{stress}}{\text{strain}} = \dfrac{FL}{A\Delta L}. Unit N m⁻². For steel, about 2×1011 N m−22 \times 10^{11}\ \text{N m}^{-2}.
  • Extension of a wire: ΔL=FLAY\Delta L = \dfrac{FL}{AY}. For one material and one load, ΔL∝Ld2\Delta L \propto \dfrac{L}{d^{2}}, since A=πd24A = \dfrac{\pi d^{2}}{4}.
  • Y depends only on the material, not on the length or thickness of the wire. A perfectly rigid body would have an infinite Y.
  • Elastic limit: the largest stress after which the wire still returns to its original length. The greatest stretch within it is ΔLmax=σlimitLY\Delta L_{max} = \dfrac{\sigma_{limit}L}{Y}.
  • Energy stored in a stretched wire: U=12FΔLU = \dfrac{1}{2}F\Delta L, that is 12×stress×strain\dfrac{1}{2} \times \text{stress} \times \text{strain} per unit volume.

Young's modulus

Y=FLAΔL,ΔL=FLAY,U=12FΔLY = \frac{FL}{A\Delta L}, \qquad \Delta L = \frac{FL}{AY}, \qquad U = \frac{1}{2}F\Delta L
  • YYYoung's modulus of the material
  • LLoriginal length of the wire
  • ΔL\Delta Lextension

Worked example

A steel wire 2 m long with a cross-section of 1 mm² holds a load of 200 N. Find its extension. (Y=2×1011 N m−2Y = 2 \times 10^{11}\ \text{N m}^{-2})
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2024 · NEET (UG) 2024 — 05 May 2024 · Q30Moderate

Example 2 · Mechanical Properties of Solids · Stress, Strain and Young's Modulus

The maximum elongation of a steel wire of 1 m length if the elastic limit of steel and its Young's modulus, respectively, are 8×1088 \times 10^{8} N m−2^{-2} and 2×10112 \times 10^{11} N m−2^{-2}, is:

Y belongs to the material, not the wire

Cutting a wire shorter or using a thinner one changes how much it stretches, but not its Young's modulus. Only a change of material changes Y.

Extension goes as one over the diameter squared

ΔL=FLAY\Delta L = \dfrac{FL}{AY} and the area grows as d2d^{2}. A wire of three times the diameter stretches one ninth as much, not one third.

The stored energy has a half in it

The force rises from zero to F as the wire stretches, so the work done is 12FΔL\dfrac{1}{2}F\Delta L, not FΔLF\Delta L.

Concept 3 of 3: Thermal stress

A heated rod wants to grow by LαΔT. If its ends are held so it cannot grow, the supports squeeze it back by exactly that much. The rod then carries the stress that would cause a strain of αΔT. The length cancels out, so a long rod and a short one of the same material feel the same stress.

Definition

  • Strain prevented in a clamped rod: αΔT\alpha\Delta T.
  • Thermal stress =YαΔT= Y\alpha\Delta T. Force on the supports: F=YAαΔTF = YA\alpha\Delta T.
  • Heating a clamped rod gives a compressive stress; cooling it gives a tensile stress.
  • The stress does not depend on the length of the rod.

Thermal stress

stress=YαΔT,F=YAαΔT\text{stress} = Y\alpha\Delta T, \qquad F = YA\alpha\Delta T
  • α\alphacoefficient of linear expansion
  • ΔT\Delta Tchange in temperature

Worked example

A brass rod is clamped between two rigid walls. By how much must its temperature rise for the thermal stress to reach 3.6×107 N m−23.6 \times 10^{7}\ \text{N m}^{-2}? (Y=1×1011 N m−2Y = 1 \times 10^{11}\ \text{N m}^{-2}, α=1.8×10−5 K−1\alpha = 1.8 \times 10^{-5}\ \text{K}^{-1})
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2024 · NEET (UG) 2024 — 05 May 2024 · Q46Moderate

Example 3 · Mechanical Properties of Solids · Stress, Strain and Young's Modulus

A metallic bar of Young's modulus, 0.5×10110.5 \times 10^{11} N m−2^{-2} and coefficient of linear thermal expansion 10−510^{-5} ∘^\circC−1^{-1}, length 1 m and area of cross-section 10−310^{-3} m2^2 is heated from 0∘^\circC to 100∘^\circC without expansion or bending. The compressive force developed in it is:

Length cancels in thermal stress

The prevented stretch is LαΔTL\alpha\Delta T and the strain divides it by L, so the stress YαΔTY\alpha\Delta T does not depend on the length.

Force needs the area

YαΔTY\alpha\Delta T is a stress. To get the force on the supports multiply by the area of cross-section: F=YAαΔTF = YA\alpha\Delta T.

Heating squeezes, cooling pulls

A clamped rod that is heated is pushed back by its supports, so it is under compression. A clamped rod that is cooled is held stretched, so it is under tension.

Summary — formulas & gotchas at a glance

A revision cheat-sheet for the formulas and gotchas above. Click any concept name to jump back to its full explanation.

Formulas (3)

  • Stress, strain and Hooke's law

    Stress and strain

    stress=FA,longitudinal strain=ΔLL,stress∝strain\text{stress} = \frac{F}{A}, \qquad \text{longitudinal strain} = \frac{\Delta L}{L}, \qquad \text{stress} \propto \text{strain}
  • Young's modulus and the elastic limit

    Young's modulus

    Y=FLAΔL,ΔL=FLAY,U=12FΔLY = \frac{FL}{A\Delta L}, \qquad \Delta L = \frac{FL}{AY}, \qquad U = \frac{1}{2}F\Delta L
  • Thermal stress

    Thermal stress

    stress=YαΔT,F=YAαΔT\text{stress} = Y\alpha\Delta T, \qquad F = YA\alpha\Delta T

Watch out for (9)

Test yourself on a real paper

Sit a past NEET paper, timed and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.

Sit a NEET past paper