PYQ Vault

NEET Physics · Units and Measurements

Vernier Callipers and Screw Gauge

Two instruments that read lengths finer than a millimetre scale: how to find their least count, how to take a reading, and how to correct it for a zero error.

Why this matters

Six NEET questions, five of them from 2024 or later. Four are on the vernier calliper: its least count from how its divisions match the main scale (2024, 2026), and a reading corrected for a zero error (2025, and Re-NEET 2026, which NTA made a bonus question). Two read a wire's diameter on a screw gauge (2021, Re-NEET 2024).

Concept 1 of 3: Vernier calliper: least count and reading

A vernier scale slides along the main scale. Its divisions are made a little shorter than the main scale divisions, so only one vernier line lines up exactly with a main scale line. How far along that line is tells you the fraction of a main scale division that the main scale alone cannot show.

Definition

  • Least count (vernier constant): LC=1 MSD−1 VSD\text{LC} = 1\ \text{MSD} - 1\ \text{VSD}.
  • If n vernier divisions equal (n−1)(n - 1) main scale divisions, 1 VSD=n−1n MSD1\ \text{VSD} = \dfrac{n-1}{n}\ \text{MSD} and LC=1 MSDn\text{LC} = \dfrac{1\ \text{MSD}}{n}.
  • In general, if N VSD equal M MSD, then 1 VSD=MN MSD1\ \text{VSD} = \dfrac{M}{N}\ \text{MSD} and LC=(1−MN)MSD\text{LC} = \left(1 - \dfrac{M}{N}\right)\text{MSD}.
  • Reading = main scale reading (the mark just before the vernier zero) + (number of the coinciding vernier division × LC).

Vernier calliper

LC=1 MSD−1 VSD,Reading=MSR+n×LC\text{LC} = 1\,\text{MSD} - 1\,\text{VSD}, \qquad \text{Reading} = \text{MSR} + n \times \text{LC}
  • nnnumber of the vernier division that coincides
  • MSR\text{MSR}main scale reading

Diagram · reading a vernier and a screw gauge

Vernier callipers: 10 VSD = 9 MSD203040mm0510zero past 23 mm6th mark lines up1 VSD = 9/10 MSD = 0.9 mmLC = 1 MSD − 1 VSD = 1 − 0.9 = 0.1 mmreading = 23 + 6 × 0.1 = 23.6 mmScrew gauge: pitch 0.5 mm, 50 divisions05253028 on the lineLC = pitch ÷ divisions = 0.5 ÷ 50 = 0.01 mmreading = 5.5 + 28 × 0.01 = 5.78 mm

The vernier's marks are each 0.1 mm shorter than the main scale's, so the first falls short of a main mark by one least count, the second by two, and the 6th lines up after six. Reading = main-scale reading + coinciding division × LC. For 25 VSD = 24 MSD with 1 MSD = 0.5 mm: LC = (1 − 24/25) × 0.5 = 0.02 mm. LC is a difference, never MSD times the number of divisions.

Worked example

In a vernier calliper 10 vernier divisions equal 9 main scale divisions, and one main scale division is 1 mm. The main scale reads 3.2 cm and the 7th vernier division coincides. Find the reading.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2026 · NEET (UG) 2026 — 03 May 2026 · Q25Moderate

Example 1 · Units and Measurements · Vernier Callipers and Screw Gauge

In a vernier calliper, 20 VSD coincide with 16 MSD (each division of length 1 mm). The least count of the vernier callipers is:

Count the divisions both ways

When N vernier divisions match M main scale divisions, one VSD is MN\tfrac{M}{N} MSD, not NM\tfrac{N}{M}. The vernier division is the shorter one.

Watch the unit in the options

Least counts are often worked in millimetres while the options are in centimetres. 0.2 mm is 0.02 cm.

Concept 2 of 3: Screw gauge: pitch, least count and reading

A screw moves forward by a fixed distance, the pitch, every time it turns once. The thimble's edge is cut into equal circular divisions, so turning by one division moves the screw by the pitch divided by that number. That tiny step is the least count, often 0.01 mm.

Definition

  • Pitch: the distance the screw moves along its axis in one full turn. Pitch = distance moved ÷ number of full turns.
  • Least count: LC=pitchnumber of circular divisions\text{LC} = \dfrac{\text{pitch}}{\text{number of circular divisions}}.
  • Reading = main (pitch) scale reading + (circular scale reading × LC).
  • More circular divisions, or a smaller pitch, gives a smaller least count.

Screw gauge

LC=pitchN,Reading=MSR+CSR×LC\text{LC} = \frac{\text{pitch}}{N}, \qquad \text{Reading} = \text{MSR} + \text{CSR} \times \text{LC}
  • NNnumber of divisions on the circular scale
  • CSR\text{CSR}circular scale reading, in divisions

Worked example

A screw gauge has a pitch of 0.5 mm and 50 circular divisions. The main scale reads 2.5 mm and the 36th circular division is on the reference line. Find the reading.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2024 · Re-NEET (UG) 2024 — 23 Jun 2024 · Q27Moderate

Example 2 · Units and Measurements · Vernier Callipers and Screw Gauge

The pitch of an error free screw gauge is 1 mm and there are 100 divisions on the circular scale. While measuring the diameter of a thick wire, the pitch scale reads 1 mm and 63rd^{rd} division on the circular scale coincides with the reference line. The diameter of the wire is:

Multiply the division number by the least count

A circular reading of 47 divisions with LC 0.01 mm adds 0.47 mm, not 47 mm and not 0.047 mm.

Pitch is per full turn

If the screw moves 1 mm in two turns, the pitch is 0.5 mm. Using 1 mm doubles the least count.

Concept 3 of 3: Zero error and the corrected reading

Close the jaws of a vernier calliper and the reading should be zero. If the vernier zero sits a little to the right of the main scale zero, every reading is too large by that amount: a positive zero error. If it sits to the left, every reading is too small: a negative zero error. You fix it by subtracting the zero error, sign included.

Definition

  • Zero error is the reading the instrument shows when the length measured is zero (jaws or studs touching).
  • Vernier zero to the right of the main scale zero: positive zero error =+n×LC= +n \times \text{LC}, where the nth vernier division coincides.
  • Vernier zero to the left: negative zero error =−(N−n)×LC= -(N - n) \times \text{LC}, where N is the number of vernier divisions.
  • Corrected reading = observed reading − zero error, with the sign of the zero error. A negative zero error is therefore added on.

Corrected reading

True reading=observed reading−(zero error)\text{True reading} = \text{observed reading} - (\text{zero error})

Worked example

A vernier calliper has 10 vernier divisions and a least count of 0.01 cm. With the jaws closed, the vernier zero lies to the left of the main scale zero and the 6th vernier division coincides. A rod then reads 2.50 cm. Find its true length.
Practise this conceptself-check · 4 quick reps

The same idea in a real exam question:

NEET · 2025 · NEET (UG) 2025 — 04 May 2025 · Q25Moderate

Example 3 · Units and Measurements · Vernier Callipers and Screw Gauge

Consider the diameter of a spherical object being measured with the help of a Vernier callipers. Suppose its 10 Vernier Scale Divisions (V.S.D.) are equal to its 9 Main Scale Divisions (M.S.D.). The least division in the M.S. is 0.1 cm and the zero of V.S. is at x=0.1x = 0.1 cm when the jaws of Vernier callipers are closed. If the main scale reading for the diameter is M=5M = 5 cm and the number of coinciding vernier division is 8, the measured diameter after zero error correction, is

Subtract the zero error, sign and all

A positive zero error is taken away; a negative one is added. Adding a positive zero error gives a reading too large by twice the error.

A negative zero error counts from the far end

When the vernier zero is left of the main zero, the error is (N−n)(N - n) divisions, not n. With 10 divisions and the 3rd coinciding it is −0.07 cm-0.07\ \text{cm} for LC 0.01 cm, not −0.03 cm-0.03\ \text{cm}.

Summary — formulas & gotchas at a glance

A revision cheat-sheet for the formulas and gotchas above. Click any concept name to jump back to its full explanation.

Formulas (3)

  • Vernier calliper: least count and reading

    Vernier calliper

    LC=1 MSD−1 VSD,Reading=MSR+n×LC\text{LC} = 1\,\text{MSD} - 1\,\text{VSD}, \qquad \text{Reading} = \text{MSR} + n \times \text{LC}
  • Screw gauge: pitch, least count and reading

    Screw gauge

    LC=pitchN,Reading=MSR+CSR×LC\text{LC} = \frac{\text{pitch}}{N}, \qquad \text{Reading} = \text{MSR} + \text{CSR} \times \text{LC}
  • Zero error and the corrected reading

    Corrected reading

    True reading=observed reading−(zero error)\text{True reading} = \text{observed reading} - (\text{zero error})

Watch out for (6)

Test yourself on a real paper

Sit a past NEET paper, timed and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.

Sit a NEET past paper