SSC CGL Tier II Maths · Free notes
Mensuration 3D: SSC CGL Tier II Maths
Mensuration 3D has 69 questions in the SSC CGL Tier II bank, second only to Percentage among the Tier II Maths chapters. 56 are EASY and 13 MODERATE, with none HARD: nearly every question is one formula and one rearrangement. Two habits carry the chapter. Know each solid's volume and surface formulas without thinking, and find the right triangle hiding inside every cone and pyramid. Most stems give pi as 22/7 and pick radii that are multiples of 7, so cancel the 7 before you multiply anything.
The handout has every subtopic, worked example, formula and trap with answers shown. The formula sheet is the chapter’s formulas and traps alone, on one page.
Subtopic notes
Cuboids, Prisms and Pyramids
19 PYQsSolids with flat faces: a cuboid and a prism hold base area times height, a pyramid holds one third of that, and their surfaces are rectangles and triangles you add up.
Cylinders
15 PYQsA cylinder is a circle stacked to a height: its volume is base area times height, its curved wall unrolls into a rectangle, and a pipe is one cylinder with another taken out.
Cones
10 PYQsA cone is built on one right triangle of radius, height and slant height; find the missing side, then use one third of the cylinder's volume or the fan-shaped curved surface.
Spheres, Hemispheres and Shells
7 PYQsA sphere is fixed by its radius alone: find r from what the stem gives, then use the volume or surface asked for; a shell is one sphere minus another, and cutting a sphere adds flat faces.
Scaling and Comparing Solids
8 PYQsAreas change with the square of a length and volumes with its cube, so a change in radius or height becomes a product of factors, and two solids compare by ratios with every constant cancelled.
Melting, Recasting and Water
10 PYQsMelting, pouring and digging change a shape but never the amount: set the old volume equal to the new one, and divide by an area, a piece's volume or a flow rate.
Formula & revision sheet
15 formulas · 17 gotchas across all subtopics — the exam-eve cheat-sheet
Formula & revision sheet
15 formulas · 17 gotchas across all subtopics — the exam-eve cheat-sheet
Formulas (3)
Watch out for (5)
- Adding the three face areas→ Cuboids: volume, faces and diagonals
- Mixing cubic centimetres and litres→ Cuboids: volume, faces and diagonals
- Taking a slanted side as the trapezium's height→ Right prisms
- Using the vertical height for the faces→ Pyramids: one third, and the slant triangles
- Mixing the slant height and the slant edge→ Pyramids: one third, and the slant triangles
Formulas (3)
Watch out for (3)
- Using the diameter as the radius→ Volume and surfaces of a cylinder
- Counting one end, or none→ Working back from a surface or a volume
- Subtracting the radii before squaring→ Hollow and drilled cylinders
Formulas (2)
Watch out for (2)
- Putting the slant height into the volume→ The cone's right triangle
- Counting the circle where two solids join→ Cone surfaces, and a cone on a hemisphere
Formulas (2)
Watch out for (2)
- Leaving out the flat face of a solid hemisphere→ Sphere and hemisphere formulas
- Forgetting the faces a cut makes→ Shells, pieces and a sphere inside a cube
Formulas (2)
Watch out for (2)
- Giving the volume the radius's percentage→ Scale factors for area and volume
- Reading a surface ratio as a volume ratio→ Ratios of two solids
Formulas (3)
Watch out for (3)
- Dividing the radii without cubing→ Counting the pieces: the volume stays the same
- Assuming the surface is kept→ Surface area after recasting
- Spreading the earth over the whole circle→ Earth dug out and water drained
PYQ weightage by concept
15 concepts · 69 PYQs — where the marks actually sit, so you know what to drill first
PYQ weightage by concept
15 concepts · 69 PYQs — where the marks actually sit, so you know what to drill first
| Concept | PYQs | Share |
|---|---|---|
| Pyramids: one third, and the slant triangles | 8 | 12% |
| Right prisms | 6 | 9% |
| Cuboids: volume, faces and diagonals | 5 | 7% |
| Concept | PYQs | Share |
|---|---|---|
| Working back from a surface or a volume | 7 | 10% |
| Volume and surfaces of a cylinder | 6 | 9% |
| Hollow and drilled cylinders | 2 | 3% |
| Concept | PYQs | Share |
|---|---|---|
| The cone's right triangle | 5 | 7% |
| Cone surfaces, and a cone on a hemisphere | 5 | 7% |
| Concept | PYQs | Share |
|---|---|---|
| Sphere and hemisphere formulas | 4 | 6% |
| Shells, pieces and a sphere inside a cube | 3 | 4% |
| Concept | PYQs | Share |
|---|---|---|
| Scale factors for area and volume | 6 | 9% |
| Ratios of two solids | 2 | 3% |
| Concept | PYQs | Share |
|---|---|---|
| Counting the pieces: the volume stays the same | 5 | 7% |
| Surface area after recasting | 3 | 4% |
| Earth dug out and water drained | 2 | 3% |
Test yourself on Mensuration 3D
20 past SSC CGL Tier II questions from this chapter, timed at 19 minutes and marked the way the exam marks it. You see your score and every answer the moment you finish. Free to start.