PYQ Vault

NEET Physics · Formula sheet

Electrostatic Potential and Capacitance formulas

10 formulas and 29 common traps for NEET Physics Electrostatic Potential and Capacitance, grouped by subtopic.

Full notes with worked examples

Electric Potential

Learn this subtopic in the notes

Potential of point charges

Point charges

V=kqr,V=∑ikqiri,k=14πε0=9×109 N m2C−2V = \frac{kq}{r}, \qquad V = \sum_i \frac{kq_i}{r_i}, \qquad k = \frac{1}{4\pi\varepsilon_0} = 9 \times 10^{9}\ \text{N m}^{2}\text{C}^{-2}
  • qqthe charge, with its sign
  • rrdistance from the charge to the point, in metres

Potential of an electric dipole

Dipole potential

p=q(2a),V=kpcos⁡θr2(r≫a)p = q(2a), \qquad V = \frac{kp\cos\theta}{r^{2}} \quad (r \gg a)
  • ppdipole moment
  • θ\thetaangle between the dipole axis and the line to the point

Charged spheres, shells and drops

Spheres and drops

Vin=kQR,Vout=kQr,Vbig drop=n2/3 VV_{\text{in}} = \frac{kQ}{R}, \qquad V_{\text{out}} = \frac{kQ}{r}, \qquad V_{\text{big drop}} = n^{2/3}\,V

Common traps

Potentials add as signed numbers

Add the potentials of several charges with their signs and no directions. Splitting them into components, as you would for fields, is wrong.

Potential falls as 1/r, field as 1/r²

Doubling the distance from a point charge halves its potential but cuts its field to a quarter.

Change centimetres to metres

With k=9×109k = 9 \times 10^{9} in SI units, a distance of 9 cm must go in as 0.09 m. Leaving it as 9 gives a potential 100 times too small.

Dipole potential goes as 1/r², not 1/r³

A dipole's field falls as 1/r31/r^{3} but its potential as 1/r21/r^{2}. The axial potential is kp/r2kp/r^{2}; a formula with 2p over r² mixes the two up and is wrong.

Zero potential does not mean zero field

On the equatorial line of a dipole the potential is zero, yet the field there is not zero. It points parallel to the axis, from + towards −.

Near the dipole, add the charges

The kpcos⁡θ/r2kp\cos\theta/r^{2} formula holds only far away. When a point is close and its distances from both charges are known, add kq/r1kq/r_1 and −kq/r2-kq/r_2 instead.

Inside a shell the potential is not zero

The field inside a charged shell is zero, so the potential there is constant and equal to kQ/RkQ/R. The potential difference between two inside points is zero, but each potential is not.

Volume adds, not radius

n drops make one drop of radius n1/3rn^{1/3}r, not nrnr. For 27 drops the radius triples and the potential becomes 9 times.

Joined spheres share potential, not charge

Charge divides in proportion to the radii. The smaller sphere ends with less charge but the larger surface charge density.

Equipotentials and Potential Energy

Learn this subtopic in the notes

Equipotential surfaces and the field

Field from potential

E=−dVdr,Ex=−dVdx,ΔV=Ed (uniform field)E = -\frac{dV}{dr}, \qquad E_x = -\frac{dV}{dx}, \qquad \Delta V = Ed \ \text{(uniform field)}

Potential energy and work

Work and potential energy

W=q(VB−VA),U=kq1q2r,12mv2=UA−UBW = q(V_B - V_A), \qquad U = \frac{kq_1q_2}{r}, \qquad \frac{1}{2}mv^{2} = U_A - U_B

Common traps

Field lines meet equipotentials at 90°

A field line always crosses an equipotential surface at right angles, never along it. If it had a part along the surface, moving a charge there would need work.

Keep the minus sign

The field is −dV/dx-dV/dx. A potential that rises with x gives a field pointing towards negative x.

Crowded surfaces mean a strong field

Where equipotentials of equal steps are close together the potential falls quickly, so the field is strong. Wide spacing means a weak field.

Keep the signs of both charges

U=kq1q2/rU = kq_1q_2/r is negative for unlike charges. Dropping the signs makes an attracted charge seem to lose speed as it falls in.

Measure from the centre of a sphere

Outside a charged sphere use kQ/rkQ/r with r from the centre. A charge at 3R from the centre is 2R from the surface, but its potential is kQ/(3R)kQ/(3R).

The path does not matter

The work to move a charge between two points depends only on their potentials, q(VB−VA)q(V_B - V_A), not on the route or tube it travels along.

Capacitors and Dielectrics

Learn this subtopic in the notes

Capacitance and the parallel plate capacitor

Parallel plate capacitor

C=QV,C=ε0Ad,E=σε0C = \frac{Q}{V}, \qquad C = \frac{\varepsilon_0 A}{d}, \qquad E = \frac{\sigma}{\varepsilon_0}
  • AAarea of each plate
  • ddgap between the plates
  • σ\sigmacharge per unit area on a plate

Dielectrics and dielectric constant

Capacitor with a dielectric

C=KC0 (gap full),C=ε0Ad−t+t/K,C=ε0A∑ti/KiC = KC_0 \ \text{(gap full)}, \qquad C = \frac{\varepsilon_0 A}{d - t + t/K}, \qquad C = \frac{\varepsilon_0 A}{\sum t_i/K_i}
  • KKdielectric constant of the slab
  • ttthickness of the slab
  • C0C_0capacitance with vacuum in the gap

Common traps

C does not depend on Q or V

Capacitance depends on the plates, their gap and the medium. Doubling Q doubles V and leaves C the same.

Ask first what stays fixed

With the battery joined, V is fixed and Q follows C. With the battery removed, Q is fixed and V follows C. Mixing these up reverses the answer.

Closer plates, larger capacitance

C=ε0A/dC = \varepsilon_0 A/d, so bringing the plates closer raises C. With a battery joined, the charge and the stored energy both rise too.

Polar means a permanent dipole

A polar molecule has a dipole moment of its own. A molecule that gets one only while a field acts is non-polar.

A thin slab changes only its own thickness

For a slab of thickness t, replace t by t/Kt/K and keep the rest of the gap as air. Multiplying the whole capacitance by K is right only when the slab fills the gap.

Count the air gap that is left

When slabs do not fill the gap, the leftover air layer is a term t/1t/1 in ∑ti/Ki\sum t_i/K_i. Forgetting it gives too large a capacitance.

Capacitor Combinations and Energy

Learn this subtopic in the notes

Series and parallel capacitors

Combinations

1Cs=∑1Ci,Cp=∑Ci,Cs=C1C2C1+C2\frac{1}{C_s} = \sum \frac{1}{C_i}, \qquad C_p = \sum C_i, \qquad C_s = \frac{C_1C_2}{C_1 + C_2}

Energy stored in a capacitor

Stored energy

U=12CV2=Q22C=12QV,u=12ε0E2U = \frac{1}{2}CV^{2} = \frac{Q^{2}}{2C} = \frac{1}{2}QV, \qquad u = \frac{1}{2}\varepsilon_0 E^{2}

Joining a charged capacitor to another

Common potential and energy lost

V=C1V1+C2V2C1+C2,ΔU=12C1C2C1+C2(V1−V2)2V = \frac{C_1V_1 + C_2V_2}{C_1 + C_2}, \qquad \Delta U = \frac{1}{2}\frac{C_1C_2}{C_1 + C_2}(V_1 - V_2)^{2}

Common traps

Capacitors combine the opposite way to resistors

Capacitors in series combine like resistors in parallel (reciprocals add), and capacitors in parallel simply add. Using the resistor rules swaps the answers.

Series capacitors share charge, not voltage

Every capacitor in a series chain carries the same charge as the equivalent capacitor. Splitting the charge among them is wrong; it is the voltage that splits.

Look for a capacitor with no voltage across it

Before adding anything, check whether a capacitor has both plates on one wire or sits across a balanced bridge. Such a capacitor holds no charge and drops out.

Use the form that holds fixed what the circuit holds fixed

With the battery joined, V is fixed, so use 12CV2\tfrac{1}{2}CV^{2}. With it removed, Q is fixed, so use Q2/2CQ^{2}/2C. The wrong form gives the wrong direction of change.

Energy density is per unit volume

12ε0E2\tfrac{1}{2}\varepsilon_0 E^{2} is energy per cubic metre. To get the energy of a capacitor, multiply by the volume between the plates, Ad.

The stored energy is half of QV

A battery that charges a capacitor to V does work QV, but the capacitor stores only 12QV\tfrac{1}{2}QV. Writing QV for the stored energy doubles it.

Charge is conserved, energy is not

When capacitors are joined, add their charges to find the common potential. Adding their energies gives too much: some energy is always lost as heat.

Equal sharing halves the energy

A charged capacitor joined to an identical uncharged one ends at half the voltage, and the two together keep only half the energy it had.

More NEET Physics formula sheets