PYQ Vault

NEET Physics · Formula sheet

Units and Measurements formulas

8 formulas, 2 reference tables and 26 common traps for NEET Physics Units and Measurements, grouped by subtopic.

Full notes with worked examples

Units and Significant Figures

Learn this subtopic in the notes

SI units and changing the unit

Changing the unit

Q=n1u1=n2u2,n∝1uQ = n_1u_1 = n_2u_2, \qquad n \propto \frac{1}{u}
  • nnnumerical value
  • uusize of the unit

Common traps

A bigger unit gives a smaller number

Since nunu stays fixed, the numerical value goes down when the unit goes up. A distance of 3 km is 3000 in metres, not 0.003.

The kilogram is the base unit of mass

The SI base unit of mass is the kilogram, not the gram. It is the only base unit whose name carries a prefix.

Temperature is in kelvin

The SI unit of thermodynamic temperature is the kelvin. The degree Celsius is not a base unit.

Sums go by decimal places

For addition and subtraction you match the fewest decimal places, not the fewest significant figures. 10.99 m + 10.0099 m is 21.00 m.

Products go by significant figures

For multiplication and division the answer keeps the significant figures of the least precise factor. 12.6 × 3.2 = 40.32 is written 4.0×1014.0 \times 10^{1}, two figures, because 3.2 has two.

Leading zeros never count

Zeros in front of the first non-zero digit only place the decimal point. 0.0025 has two significant figures, not four.

Dimensions and Dimensional Analysis

Learn this subtopic in the notes

Principle of homogeneity

Homogeneity

x=a+bt+ct2 ⇒ [x]=[a]=[bt]=[ct2]x = a + bt + ct^{2} \ \Rightarrow\ [x] = [a] = [bt] = [ct^{2}]

Deriving relations and changing base quantities

Method of dimensions

Q=k axbycz,n2=n1[M1M2]a[L1L2]b[T1T2]cQ = k\,a^{x}b^{y}c^{z}, \qquad n_2 = n_1\left[\frac{M_1}{M_2}\right]^{a}\left[\frac{L_1}{L_2}\right]^{b}\left[\frac{T_1}{T_2}\right]^{c}

Dimensional formulae of common quantities

QuantityDefining relationDimensions
ForceF=maF = ma[MLT−2][MLT^{-2}]
Work, energy, torqueW=FsW = Fs[ML2T−2][ML^{2}T^{-2}]
PowerP=W/tP = W/t[ML2T−3][ML^{2}T^{-3}]
Momentum, impulsep=mvp = mv[MLT−1][MLT^{-1}]
Angular momentum, Planck's constantL=mvr, E=hνL = mvr,\ E = h\nu[ML2T−1][ML^{2}T^{-1}]
Pressure, stress, Young's modulusF/AF/A[ML−1T−2][ML^{-1}T^{-2}]
Surface tension, spring constantF/lF/l[MT−2][MT^{-2}]
Coefficient of viscosityF=ηA dvdzF = \eta A\,\dfrac{dv}{dz}[ML−1T−1][ML^{-1}T^{-1}]
Gravitational constant GF=Gm1m2r2F = \dfrac{Gm_1m_2}{r^{2}}[M−1L3T−2][M^{-1}L^{3}T^{-2}]
Latent heatQ/mQ/m[L2T−2][L^{2}T^{-2}]
Chargeq=Itq = It[AT][AT]
Potential differenceV=W/qV = W/q[ML2T−3A−1][ML^{2}T^{-3}A^{-1}]
Permittivity of free spaceF=q1q24πε0r2F = \dfrac{q_1q_2}{4\pi\varepsilon_0 r^{2}}[M−1L−3T4A2][M^{-1}L^{-3}T^{4}A^{2}]
Permeability of free spaceμ0ε0=1c2\mu_0\varepsilon_0 = \dfrac{1}{c^{2}}[MLT−2A−2][MLT^{-2}A^{-2}]Q
NEET 2022: which quantity has the dimensions MLT⁻²A⁻²? The answer was magnetic permeability.
Magnetic fluxε=dΦdt\varepsilon = \dfrac{d\Phi}{dt}[ML2T−2A−1][ML^{2}T^{-2}A^{-1}]
Stefan constant, Boltzmann constant, Wien's constantσT4, 32kBT, λmT=b\sigma T^{4},\ \tfrac{3}{2}k_BT,\ \lambda_m T = b[MT−3K−4][MT^{-3}K^{-4}], [ML2T−2K−1][ML^{2}T^{-2}K^{-1}], [LK][LK]Q
Re-NEET 2026 combined all three: the dimensions of the Stefan constant divided by the Boltzmann constant, times Wien's constant.
Plane angle, solid angle, strains/r, A/r2, Δl/ls/r,\ A/r^{2},\ \Delta l/l[M0L0T0][M^{0}L^{0}T^{0}]Q
NEET 2022: plane and solid angle have units but no dimensions. NEET 2024: strain and angle have the same dimensions as solid angle.
Each row follows from its defining relation. σT⁴ is power per unit area, and (3/2)k_BT is an energy.

Common traps

Having a unit does not mean having dimensions

Radian and steradian are units, but angle and solid angle are ratios of like quantities, so their dimensions are [M0L0T0][M^{0}L^{0}T^{0}].

Same dimensions, different quantity

Work and torque share [ML2T−2][ML^{2}T^{-2}], and angular momentum and Planck's constant share [ML2T−1][ML^{2}T^{-1}]. Matching dimensions does not make two quantities the same thing.

G carries a negative power of mass

From G=Fr2m1m2G = \dfrac{Fr^{2}}{m_1m_2}, G is [M−1L3T−2][M^{-1}L^{3}T^{-2}]. Dividing by m2m^{2} leaves M−1M^{-1}, not M−2M^{-2}.

Correct dimensions, wrong formula

s=ut+at2s = ut + at^{2} passes the dimension test but is wrong; the right one has 12at2\tfrac{1}{2}at^{2}. Dimensions can reject a formula, never prove it.

A constant takes the dimensions of what it is added to

In (P+aV2)\left(P + \dfrac{a}{V^{2}}\right), with P a pressure and V a volume, the term aV2\dfrac{a}{V^{2}} is a pressure, so a is [ML5T−2][ML^{5}T^{-2}]. Match the whole term, including its power, not the bare letter.

Converting time squares the factor

Going from seconds to minutes in an acceleration multiplies by 60260^{2}, not 60, because time appears as T−2T^{-2}.

Check the answer by putting it back

After solving for the powers, rebuild the dimensions from your answer. A sign slip in one power is the usual way to land on a wrong option.

Errors in Measurement

Learn this subtopic in the notes

Combining errors in sums, differences, products and quotients

Combining errors

Z=A±B: ΔZ=ΔA+ΔB,Z=AB or AB: ΔZZ=ΔAA+ΔBBZ = A \pm B:\ \Delta Z = \Delta A + \Delta B, \qquad Z = AB \text{ or } \frac{A}{B}:\ \frac{\Delta Z}{Z} = \frac{\Delta A}{A} + \frac{\Delta B}{B}

Errors in a product of powers

Error in a product of powers

Z=ApBqCr ⇒ ΔZZ=pΔAA+qΔBB+rΔCCZ = \frac{A^{p}B^{q}}{C^{r}} \ \Rightarrow\ \frac{\Delta Z}{Z} = p\frac{\Delta A}{A} + q\frac{\Delta B}{B} + r\frac{\Delta C}{C}

Kinds of error, and how big an error is

ErrorCauseHow to reduce it
Instrumental errorFaulty design or calibration, such as a zero errorCorrect for it, or use a better instrument
Error of methodAn imperfect technique, such as a thermometer under the armpit reading below the true body temperatureImprove the procedure
Personal errorThe observer's bias or carelessness, such as reading a scale at an angle (parallax)Take care while reading
Random errorUnpredictable changes in temperature, pressure or supply voltageRepeat many times and take the mean
NEET 2023 asked which error comes from unpredictable changes in temperature and voltage supply: random errors.
Least count errorThe smallest division the instrument can showUse a finer instrument and repeat the reading
The first three are systematic: they push every reading the same way, so averaging does not remove them.

Common traps

Averaging only beats random errors

Repeating a reading and taking the mean reduces random errors. A systematic error, such as a zero error, stays in every reading and in the mean.

Precise is not the same as accurate

Readings can agree closely with each other and still all be wrong by the same amount. That is high precision and low accuracy.

A difference still adds the errors

For Z=A−BZ = A - B the error is ΔA+ΔB\Delta A + \Delta B, never ΔA−ΔB\Delta A - \Delta B. Errors never cancel.

Absolute for sums, relative for products

In a sum the absolute errors add; in a product or quotient the relative (or percentage) errors add. Adding absolute errors for a quotient gives a wrong answer.

The power multiplies the error

For r2r^{2} the relative error is 2Δrr2\dfrac{\Delta r}{r}. Leaving out the 2 is the most common slip in a density or volume question.

Denominator terms are added too

A quantity in the denominator still adds its error. In Z=A/C2Z = A/C^{2} the error is ΔAA+2ΔCC\dfrac{\Delta A}{A} + 2\dfrac{\Delta C}{C}, not a difference.

A square root halves the error

For d\sqrt{d} the relative error is 12Δdd\tfrac{1}{2}\dfrac{\Delta d}{d}. A 6% error in d becomes 3%, not 6% or 12%.

Vernier Callipers and Screw Gauge

Learn this subtopic in the notes

Vernier calliper: least count and reading

Vernier calliper

LC=1 MSD−1 VSD,Reading=MSR+n×LC\text{LC} = 1\,\text{MSD} - 1\,\text{VSD}, \qquad \text{Reading} = \text{MSR} + n \times \text{LC}
  • nnnumber of the vernier division that coincides
  • MSR\text{MSR}main scale reading

Screw gauge: pitch, least count and reading

Screw gauge

LC=pitchN,Reading=MSR+CSR×LC\text{LC} = \frac{\text{pitch}}{N}, \qquad \text{Reading} = \text{MSR} + \text{CSR} \times \text{LC}
  • NNnumber of divisions on the circular scale
  • CSR\text{CSR}circular scale reading, in divisions

Zero error and the corrected reading

Corrected reading

True reading=observed reading−(zero error)\text{True reading} = \text{observed reading} - (\text{zero error})

Common traps

Count the divisions both ways

When N vernier divisions match M main scale divisions, one VSD is MN\tfrac{M}{N} MSD, not NM\tfrac{N}{M}. The vernier division is the shorter one.

Watch the unit in the options

Least counts are often worked in millimetres while the options are in centimetres. 0.2 mm is 0.02 cm.

Multiply the division number by the least count

A circular reading of 47 divisions with LC 0.01 mm adds 0.47 mm, not 47 mm and not 0.047 mm.

Pitch is per full turn

If the screw moves 1 mm in two turns, the pitch is 0.5 mm. Using 1 mm doubles the least count.

Subtract the zero error, sign and all

A positive zero error is taken away; a negative one is added. Adding a positive zero error gives a reading too large by twice the error.

A negative zero error counts from the far end

When the vernier zero is left of the main zero, the error is (N−n)(N - n) divisions, not n. With 10 divisions and the 3rd coinciding it is −0.07 cm-0.07\ \text{cm} for LC 0.01 cm, not −0.03 cm-0.03\ \text{cm}.

More NEET Physics formula sheets