PYQ Vault

NEET Physics · Formula sheet

Current Electricity formulas

10 formulas and 23 common traps for NEET Physics Current Electricity, grouped by subtopic.

Full notes with worked examples

Current, Drift and Resistivity

Learn this subtopic in the notes

Current, drift velocity and current density

Current and drift

I=neAvd,vd=eEτm,J=nevd=σEI = neAv_d, \qquad v_d = \frac{eE\tau}{m}, \qquad J = nev_d = \sigma E
  • nnfree electrons per unit volume
  • τ\taurelaxation time
  • vdv_ddrift velocity

Resistance, resistivity and conductivity

Resistance

R=ρLA,ρ=mne2τ=EJ,Rstretched=n2RR = \frac{\rho L}{A}, \qquad \rho = \frac{m}{ne^{2}\tau} = \frac{E}{J}, \qquad R_{\text{stretched}} = n^{2}R

Temperature dependence of resistance

Temperature coefficient

RT=R0[1+α(T−T0)],α=RT−R0R0(T−T0)R_T = R_0\left[1 + \alpha (T - T_0)\right], \qquad \alpha = \frac{R_T - R_0}{R_0 (T - T_0)}

Common traps

Area goes as the diameter squared

Halving a wire's diameter cuts its area to a quarter, so for the same current the drift velocity becomes four times, not two times.

Drift is slow, the signal is not

Drift velocity is only about a millimetre per second. A bulb lights at once because the field sets up along the whole wire almost instantly, not because electrons race from the switch.

Resistivity belongs to the material

Cutting, stretching or bending a wire changes its resistance, never its resistivity. Only a change of material or temperature changes ρ.

Stretching scales by n squared

Stretching to n times the length also shrinks the area by n, because the volume stays the same. The resistance becomes n2Rn^{2}R, not nRnR.

The third band is a multiplier

In the colour code the third band is the number of zeros, not a third digit. 22000 Ω is red, red, orange.

Divide by R at the reference temperature

In α=RT−R0R0 ΔT\alpha = \dfrac{R_T - R_0}{R_0\,\Delta T} the denominator uses the resistance at the reference temperature, not the final one.

Semiconductors go the other way

Resistance rises with temperature for metals but falls for semiconductors. A statement that it rises or falls for both is false.

Combinations of Resistors

Learn this subtopic in the notes

Series and parallel combinations

Equivalent resistance

Rs=R1+R2+…,1Rp=1R1+1R2+…,RsRp=n2R_s = R_1 + R_2 + \dots, \qquad \frac{1}{R_p} = \frac{1}{R_1} + \frac{1}{R_2} + \dots, \qquad \frac{R_s}{R_p} = n^{2}

Current division and steady state

Current divider

I1=I R2R1+R2,I2=I R1R1+R2I_1 = I\,\frac{R_2}{R_1 + R_2}, \qquad I_2 = I\,\frac{R_1}{R_1 + R_2}

Common traps

Find one piece first

When a wire is cut, each piece carries its share of the original resistance, R/nR/n. Using the whole wire's R for a piece makes every later step wrong.

The current ratio is n squared

Switching n equal resistors from series to parallel on the same battery multiplies the current by n2n^{2}, not n, because the resistance falls from nR to R/n.

Stretch, then bend

A wire stretched to twice its length has four times its resistance before it is bent. Across a diameter the circle then gives a quarter of that new value.

Each branch takes the other's resistance

In I1=IR2/(R1+R2)I_1 = I R_2/(R_1 + R_2) the numerator is the OTHER branch's resistance. Putting R1R_1 on top gives the larger current to the larger resistor, which is backwards.

A full capacitor is an open switch

In the steady state no current flows through a capacitor's branch. Leaving that branch in the resistance calculation gives a wrong total.

Power, Cells and EMF

Learn this subtopic in the notes

Electrical power and ratings

Power

P=VI=I2R=V2R,R=V02P0,P=P0(VV0)2P = VI = I^{2}R = \frac{V^{2}}{R}, \qquad R = \frac{V_0^{2}}{P_0}, \qquad P = P_0\left(\frac{V}{V_0}\right)^{2}

Emf, internal resistance and terminal voltage

Terminal voltage

I=ER+r,V=E−Ir,Eeq=E1r2+E2r1r1+r2I = \frac{E}{R + r}, \qquad V = E - Ir, \qquad E_{eq} = \frac{E_1r_2 + E_2r_1}{r_1 + r_2}

Common traps

In parallel the smaller resistor heats more

Parallel resistors share a voltage, so heat goes as V2/RV^{2}/R: the smaller resistor gives more heat. Using I2RI^{2}R with one current gets the order backwards.

Power goes as the square of the voltage

Dropping a supply from 220 V to 200 V does not cut the power by 20/220. Square the factor: (200/220)2(200/220)^{2} is about 0.83.

In series the lower rating glows more

A 25 W bulb has more resistance than a 100 W bulb of the same voltage, so with the same current it dissipates more. In parallel the order flips.

Subtract only the drop inside the cell

Terminal voltage is E−IrE - Ir, with the internal resistance r. Subtracting IRIR with the external resistance gives zero, not the terminal voltage.

Parallel cells do not add their emfs

Identical cells in parallel keep the emf of one cell and divide the internal resistance by n. Only cells in series add their emfs.

Kirchhoff's Rules and Bridges

Learn this subtopic in the notes

Kirchhoff's junction and loop rules

Kirchhoff's rules

∑Iin=∑Iout,∑loopΔV=0\sum I_{\text{in}} = \sum I_{\text{out}}, \qquad \sum_{\text{loop}} \Delta V = 0

The Wheatstone bridge

Balance condition

PQ=RS⇒Ig=0\frac{P}{Q} = \frac{R}{S} \quad\Rightarrow\quad I_g = 0

The metre bridge and the potentiometer

Balance on a uniform wire

RS=l100−l,E1E2=l1l2\frac{R}{S} = \frac{l}{100 - l}, \qquad \frac{E_1}{E_2} = \frac{l_1}{l_2}

Common traps

Opposing cells subtract

Two cells joined positive to positive in one loop push against each other. The net emf is the difference, and the current goes the way the larger emf pushes.

Keep the signs in step with your guess

Once a current direction is guessed, use the same direction for every IR term in every loop. Switching mid-way is the commonest source of a wrong answer.

Check the ratio before using Kirchhoff

Before writing loop equations, test P/Q=R/SP/Q = R/S. If it holds, the middle arm drops out and the circuit is plain series and parallel.

The middle arm does not matter at balance

At balance the galvanometer arm carries no current whatever its resistance, so a 2 Ω, a 10 Ω or a plain wire there gives the same total.

Measure each part from its own end

The length beside the left resistor is measured from the left end; the other part is the rest of the wire. A question asking for the distance from the other end wants L−lL - l.

Swapping the cell and galvanometer keeps the balance

The balance condition depends only on the four resistances, so interchanging the cell and galvanometer leaves the null point where it was.

More NEET Physics formula sheets